CarlinoJoeVideo

S200x600_jessy1_1471467436

Lives in: Portland/Los Angeles, CA USA

Member since: 11/30/13

Recent Activity Filter:

Added reply in a thread Titanium rotors 11/30/2017 6:16 PM

Funny this topic came up. A friend of mine from London was just telling me that his dad used to make carbon discs for the MotoGP guys in Europe. When he was riding 85s his dad made him a prototype setup. He said it was insane but looked crazy. I’ll see ... more »

Added reply in a thread Do these fork lug covers also fit Cone Valves? 11/30/2017 6:12 PM

4cs have more of a rounded lug than the CVs. They are machined with more of a square edge. They might fit but Maybe not perfect.

Added reply in a thread Vote for me in the 2017 Pulpys? Ha... 11/30/2017 6:09 PM

I

Added reply in a thread Is this the 2018 Husky factory edition? 11/29/2017 8:36 PM

Yes, I’d put money on it. The rumor is that it will be called “Race Edition”.

Added reply in a thread Is this the 2018 Husky factory edition? 11/29/2017 4:08 AM

Id love to think that is the Husky "Race Edition" but I saw that post on Instagram and they were advertising the new triple clamps. Maybe its a leak? I feel like those AER CVs didn't get the attention they thought, so could be a way to get them out the ... more »

Added reply in a thread Wp cone valve forks 11/26/2017 11:54 PM

Sent you PM. How can I get ahold of you?

Added reply in a thread what happened to the 2018 crf 250? 11/26/2017 11:47 PM

For me the Honda chassis and suspension are so good off the showroom room. The engine is good, it’s got way more power than most people are getting the impression. I honestly really love the stock suspension. The KTM has a great chassis and engine out ... more »

Added reply in a thread Keep or get rid of 2016 FC250 11/26/2017 3:44 PM

I don’t remember the exact amount. But it’s the full clutch, basket ect. It uses a round pressure spring instead of 5 coil springs. I’d say around $1,000? They have 25% off today.

Added reply in a thread 2016.5 KTM 450 Factory Editions and 52mm forks 11/26/2017 2:06 AM

I sent you an email. Let me know when you have time!

Added reply in a thread Keep or get rid of 2016 FC250 11/26/2017 1:29 AM

Hinson has a cush drive clutch for the 250s like the 450s have. There's rubber dampers that take harsh hit off the tranny. It's not on their site, but call them. I've ran mine for 35 hours and love it over the stock feel.

Added reply in a thread Keep or get rid of 2016 FC250 11/26/2017 1:27 AM

If you are really worried about your tranny and willing to spend $2800. I would send the engine to some in California like Twisted Devolopment. Have them do your top end, replace the gears that have been breaking as well as micro-polish your tranny and ... more »

Added reply in a thread Ktm 350 no spark 11/25/2017 5:46 AM

Maybe remove the tip over sensor. Check all the grounds around the coil. Make sure there’s no paint and it’s true metal on metal.

Added reply in a thread Psi? 11/25/2017 5:43 AM

I run 12.5-13 on Dunlop Mx3S and when I had Michelin Starcross 5 I went to 14-14.5 because the sidewalks felt so soft.

Liked a bike check 2017 KTM 250sx TLD Limited Edition Plastics 11/25/2017 5:31 AM
S780_botd173
Added reply in a thread 2016.5 KTM 450 Factory Editions and 52mm forks 11/24/2017 12:56 AM

What are the offset on the clamps? Do you come to So cal, I see your are in NV. Thanks! Can I PM or email you?

Added reply in a thread Black Friday specials 11/24/2017 12:51 AM

Added reply in a thread 2016.5 KTM 450 Factory Editions and 52mm forks 11/23/2017 6:44 AM

So you are sell 2 sets of 52mm? What is the difference, sorry I was confused by the way it was listed above. Thank you!

Added reply in a thread 2016 WP cone valves 11/22/2017 7:23 PM

Before I read all the comments I thought you were serious! ... more »

Added reply in a thread 2013 KTM 85 SXS won't shift! 11/22/2017 7:16 PM

Does the shifter move or is the shifter itself stuck?

Added reply in a thread what TP199 did 11/20/2017 5:46 PM

I’d say 4 flips based on that ramp. Or some kind of triple flip variation...