LumpDog841

S200x600_v8_1481571558

Lives in: MI, USA

Member since: 12/12/16

Recent Activity Filter:

Added reply in a thread This type of sh*t... 10/12/2017 6:32 PM

Found his facebook, and according to hookit he's sponsored by Spy and Scott...lol

Added reply in a thread Ryan Villopoto, Chad Reed to Race Red Bull Straight Rhythm 10/5/2017 10:08 AM

Seriously, would love to see RV out there on his SR250 that he rode in the TWMX premix videos.

Added reply in a thread '17 250SX stiff throttle pull 10/3/2017 10:54 AM

Yeah I installed an entire G2 setup hoping it would solve it. Unfortunately it didn't really make a difference. Setup I used: https://www.g2ergo.com/store/ktmhusky-2-stroke-throttle-upgrade-kit/

Added reply in a thread '17 250SX stiff throttle pull 10/3/2017 10:49 AM

Yeah, it's pretty bad. Just bought a new carb, which should be here Fri. As long as I don't get sucked into work I'll be at coops wed!!!

Added reply in a thread '17 250SX stiff throttle pull 10/2/2017 7:18 PM

Started new thread '17 250SX stiff throttle pull 10/2/2017 7:13 PM

Ok, I tried everything I can think of (cables, throttle housing, springs, handlebar bearings) and was wondering if anyone else has a really stiff throttle pull/twist on their 250SX (Mikuni carb). From the photos below, I believe there is something wrong

... more »

This forum thread has 7 replies

Added reply in a thread Cone Valve-AER48-4CS Ride Height? 10/1/2017 7:05 PM

I honestly haven't. Though they appear to be exactly the same, but I don't have actual numbers to back that up. One weird thing though is the CV forks seem to fit better in the xtrig clamps...maybe better dimensional tolerance?

Added reply in a thread 2017 KTM 250SX Build 10/1/2017 3:29 PM

I am, at the moment though I just purchased an Acerbis X-Seat, which is the stock height. I will probably go back to the stock height as I feel the taller seat sort of screws up the handling. I'm about 6 foot tall (183 cm), maybe 6'1" (185 cm) with boots ... more »

Added reply in a thread 2017 KTM 250SX Build 10/1/2017 3:24 PM

Lol, It's sort of a problem as I don't know what to do with the empty cans....

Added reply in a thread Cone Valve-AER48-4CS Ride Height? 10/1/2017 3:23 PM

Running mine on the second line for the CV forks, same as I ran with the AER. For sag I'm running around ~107 mm, though it's been two weeks since I checked it.

Added a comment to Vadim's bike check 9/28/2017 7:12 PM
S780_p1080736

Beautiful bike.

0 0 0

This setup has 1 comment.

Added reply in a thread 2017 KTM 250SX Build 9/28/2017 7:07 PM

A few race day shots. ... more »

Added reply in a thread 2017 KTM 250SX Build 9/28/2017 7:04 PM

Thanks bud.

Added reply in a thread 2017 KTM 250SX Build 9/28/2017 7:03 PM

Thanks, I have an 06 YZ125. I'll see if that works.

Added reply in a thread 2017 KTM 250SX Build 9/28/2017 6:59 PM

Yeah, after I go through my stock of oem springs that is what I'm going with. I ended up sealing the cover with high temp silicon, which seems to work.

Added reply in a thread Cone valve popping?? 9/20/2017 6:09 PM

I use these to adjust my comp clickers. Used the Ride Eng ones in the past, bit of a pain to setup, but work well. https://www.rockymountainatvmc.com/p/731/61208/Race-Tech-Fork-Compression-Adjuster-Tool

Added reply in a thread Tom Morgan? 9/20/2017 10:33 AM

I know I feel the same way, heard a lot of great things about him. It was over 10 years ago, stuff happens though. If I remember correctly he admitted he got swamped with work and my stuff got farmed out. Truthfully I wouldn't have a problem sending ... more »

Added reply in a thread Show us your 17 250SX 9/19/2017 7:21 PM

Little action shot from a few weeks ago, chasing another 17 250SX

Added reply in a thread Tom Morgan? 9/19/2017 7:17 PM

Honestly I think I may be the only one on the planet that had a bad experience with Tom Morgan.