GCBC

GCBC

Lives in: Pittsburgh, PA USA

Member since: 11/19/17

Recent Activity Filter:

Added reply in a thread Poll - Middle Finger 3/28/2020 8:27 PM

I wish there was a more offensive gesture to give.

Added reply in a thread 2020 KX250 Bang 4 Buck Build 3/28/2020 5:45 PM

Haven’t rode it yet but from what I’m hearing it makes every bit as much power as a new ktm now and 14300rpm

Added reply in a thread Chad done?? Race bikes for sale.. 3/28/2020 4:32 PM

now im getting an email doesn't work response....

Added reply in a thread Husqvarna FC Graphics 3/28/2020 4:17 PM

I just did the plates with the thing that comes up the side. think it looks clean and factory. If I pick up a new 20 husky instead of another ktm id probably get the all blue plastic and start from that point. the white looks like shit after the first

... more »

Added reply in a thread Least safe helmets? 3/28/2020 3:42 PM

they should make ones with raised sides so the foam hits your collarbone instead of the edge of the shell.

Added reply in a thread Titanium Spokes! 3/28/2020 3:39 PM

Anyone doing different lacing patterns? like in MTB world there's multiple lace patterns.

Added reply in a thread 18 Husqvarna FC250, Pennsylvania 3/28/2020 5:41 AM

Definitely a cool setup. Will see what happens this coming week.

Added reply in a thread 2019 KX450 Front Brake 3/27/2020 9:09 PM

push pistons all the way into calipers with the res cap off, then preceded to tap line/caliper and bleed it.

Added reply in a thread Carbon Fiber Coffee Table Inlay Questions 3/27/2020 9:06 PM

OP, looks nice. working with cf is a precise labor of love... I have these if anyones interested. Will trade for a bike... https://www.ebay.com/itm/321702295186 https://www.ebay.com/itm/321702296075

Added reply in a thread Severley Broken Pelvis- getting back in the saddle 3/27/2020 6:18 AM

best wishes. Looks like your in good shape so that will make things easy. Deff don't sell all your stuff until you ride the first time again, I made that mistake 8months ago...

Added reply in a thread The supercross season is not over. 3/27/2020 6:15 AM

Over promise & under deliver. Its the American way.

Added reply in a thread Chad done?? Race bikes for sale.. 3/26/2020 9:11 PM

here we go...

Added reply in a thread I took vital’s advice and bought a new bike 3/25/2020 8:44 PM

so damn sexy.

Liked a comment on the item 2020 Vital MX 450 Off-Road Shootout 3/25/2020 8:24 PM

It isnt just a high hp engine. It makes more power at every rpm from 4k on up as shown on the dyno.

Added reply in a thread cycling recommendation 3/25/2020 3:42 PM

get a slightly used cannonade supersix off PINKBIKE for 3500-4000 that was a 8k bike a year ago. if MTB and not doing jumps bigger than say 10-15ft go with an XC bike, like a 12-15 cannonade scalpel 29er in carbon I run "egg beaters" for pedals on my ... more »

Added reply in a thread KTM/Husky to Japanese front end swap? 3/25/2020 1:17 PM

alright, I get it. no switcharoo. Will be reviewing options. Id have zero hesitation to spend 5k on a set of forks and shock if I know I could take them from bike to bike for a few years bouncing from a 20' 150sx to a 22' 350sxf to a 23' whatever.... ... more »

Added reply in a thread Not good at all (Mat Mladin) 3/25/2020 1:02 PM

need more info.

Added reply in a thread 2015 Yamaha Yz250f for sale 3/25/2020 10:44 AM

those are some cool graphics

Added reply in a thread Why anodize aluminum frame 3/25/2020 9:51 AM

all im going to say is if anyones doing it for anything other than purely cosmetic reasons your better off cyro'ing it instead if your looking to do anything with its rigidity. ano is much lighter than pc obviously and I can see pc reducing compliance ... more »

Added reply in a thread KTM/Husky to Japanese front end swap? 3/24/2020 9:46 PM

gotcha so wheel width:fork tube center points are all the same its as simple as clamp diameters?