Lives in: Louisburg, KS USA

Member since: 07/30/13

Recent Activity Filter:

Added reply in a thread Idaho Budget 02 CR250R Rebuild 12/12/2019 12:30 PM

I have a airstyker and didn't have to make any mods to the airbox

Added reply in a thread Spokes pops when lightly tightened ? 12/3/2019 8:44 PM

Thats normal

Added reply in a thread LOOKING FOR CR125 2005-2007 CLUTCH-IGNITION COVER AFTERMARKET 10/16/2019 7:48 AM

Added reply in a thread KLX 140 carburetor swap 8/20/2019 11:56 AM

I swapped a ttr125 with a kx65 carb. You will need bigger carb clamps as the OEM ones didn't work. It was also a little tighter fit. Overall it made it run way better and with a few needle adjustments (clip position). Pretty sure I had to drill out the ... more »

Added reply in a thread 07 CR250R airbox boot raised # 8/18/2019 1:42 PM

Thats what my 07 says just went out and checked.

Added reply in a thread 2007 crf slight ticking noise 7/28/2019 7:11 AM

A worn timing chain will do that.

Added reply in a thread 98 team Pro Circuit MXDN replica 7/15/2019 3:00 PM

If it has sand in the air boot and carb, there is going to be sand in the crank area. I would advise to split the cases and clean everything out. You could also flush the crankcase with diesel or two stroke fuel if you do not want to take it apart.

Added reply in a thread Parting out 2005 Honda CR250 6/25/2019 1:40 PM

Those 05-07 frames are pretty rare. I sold a 05 frame with a broken exhaust mount and no title for $200+ shipping

Added reply in a thread ISO cr subframe 6/3/2019 3:44 PM

A cr250 subframe will also work it just has two silencer mounting points vs 1

Added reply in a thread 2007 cr250 5/1/2019 6:25 AM

I have a HGS racing pipe on mine and it spread the power out more and really picked up power over a Procircuit Platinum. I recommend it the fitment was great.

Added reply in a thread 1999 RM 144 anti freeze leak 4/17/2019 1:51 PM

Those washers under the acorn nuts need replaced every time you take it apart. They are crush type

Added reply in a thread Can a spark plug be bad without fouling? 3/20/2019 5:44 AM

Yes a spark plug can be bad without fouling. They are cheap and the first thing I change out when a bike isn't running properly. A leak down test will tell you if any of the seals or gaskets are leaking in the combustion side of the engine. This includes ... more »

Added reply in a thread Mistiming the crankshaft 3/20/2019 5:41 AM

If you turned it over by hand and there was no binding only your timing was off your okay. As you stated you disassembled to check for damage and if you didn't see anything reassemble with fresh head gasket and your good to go.

Added reply in a thread CR125 big bored to 144cc has marks on the exhaust bridge (photo) 3/20/2019 5:34 AM

Exhaust bridge is fine it looks to have been relieved a little bit when it was replated which is normal it helps with cracking and catching of the piston. Use a little scotch-brite green and wd40 to knock off the glaze on the inside of the cylinder. ... more »

Added reply in a thread ISO 94-97 cr125 procircuit pipe even if it’s trashed 3/13/2019 1:22 PM

Are the 92 -93 pipes different? There is a used works 92 on Ebay

Added reply in a thread Kellerdiesnt niche, '04 SX200 3/10/2019 5:50 AM

That bike has a stroked crank or long rod. It has a spacer under the cylinder

Added reply in a thread 05 CRF250R issues 3/8/2019 10:51 AM

That sounds like your issue. Spring, washer, then o-ring. Set the screw at 1.75 turns out for a baseline.

Added reply in a thread 05 CRF250R issues 3/8/2019 6:00 AM

The rubber boot that attaches the carb and the head could be cracked. Sounds like its running very lean. Did you set the fuel screw on the bottom of the carb? It has a little washer/o-ring on the tip of it and if its not in place it will run lean.

Added reply in a thread CR125 chipped cylinder 2/27/2019 12:36 PM

Yes new cylinder. A nikasil cylinder is superior to a sleeved cylinder. There is a reason manufactures went away with lined cylinders. If the engine is properly rebuilt and maintained a nikasil cylinder will last longer on the bore and have better heat ... more »

Added reply in a thread CR125 chipped cylinder 2/27/2019 11:23 AM

Looks like the sleeve is off center/rotated. That cylinder is trash and if they ground on the power valve those too. Look for a non-sleeved used cylinder or new OEM.