YZed250

YZed250

Lives in: Costa Mesa, CA USA

Member since: 11/09/14

Recent Activity Filter:

Added reply in a thread KTM 250SX Keihin PWK 36 Jetting? 1/17/2019 5:02 PM

Bump Anyone?

Added reply in a thread Spoke with my wallet (for reals) 1/17/2019 1:44 PM

The 19s have the closed off airbox, so you might find this jetting (above) is a little rich. I just jumped on a 17 and I am a very happy camper. Here are my suggestions onthe carb, or mods that I plan to do to mine: 1. Notch the slide on the intake side. ... more »

Added reply in a thread D37 Sprint Enduro 1/17/2019 11:04 AM

Check out Sarah Alvarado photo. She has a handful of shots on her Instagram and they are out of this world.

Added reply in a thread D37 Sprint Enduro 1/16/2019 11:24 PM

Anyone have pics of me? Red #76 on a KTM 250SX on AB

Added reply in a thread D37 Sprint Enduro 1/16/2019 11:22 PM

Nice!

Added reply in a thread D37 Sprint Enduro 1/16/2019 10:39 PM

Yes, I got a about a 4-inch rock dent in my 250sx pipe and that hasn't happened to this old vet GP racer in quite a few seasons of racing.

Added reply in a thread Yamaha Flexible Flyer 1/16/2019 9:56 AM

Thought this thread was go0ing to be about Taka Higahino. Flexible flyer, huh? Those are cool too.

Added reply in a thread D37 Sprint Enduro 1/16/2019 9:39 AM

https://www.youtube.com/watch?v=KfSebIx8HXI&t=329s

Started new thread KTM 250SX Keihin PWK 36 Jetting? 1/14/2019 1:32 PM

Anyone have a baseline jetting specs for running a Keihin carb on the new KTM 250cc motor? I'm running a stock engine with a pipe and around sea level and 100ll/91Oct mix, 50:1. I heard the new 250 motor needs more fuel than the 2016 and older 250SX, ... more »

This forum thread has 5 replies

Started new thread WTB Keihin PWK 36 or 38mm carb 1/14/2019 12:29 PM

Looking for a two-bolt flat slide Keihin PWK, either in 36 or 38 mm dia. I am located in SoCal, Costa Mesa CA.

This forum thread has 2 replies

Added reply in a thread PWK38 with powerjet.....how do i remove the powerjet? 1/10/2019 3:02 PM

Ride report? YZ250 slide work okay?

Added reply in a thread 2017 250SX idle gear case break? 1/8/2019 10:29 AM

What tap to use in the hole? Finishing M10 or M8 x ?

Added reply in a thread Turning a 125 sx or tc into 150 xcw or te 1/2/2019 1:59 PM

I just rode a 2018 300xcw yesterday, and I can't believe how good that thing is for trail riding. The 250/300 is a few pounds heavier, but is ultra-uber torquey. That might give you a few more options for a used bike search if you're willing to deal ... more »

Added reply in a thread Turning a 125 sx or tc into 150 xcw or te 1/2/2019 1:54 PM

Most of the KTMs are very tuneable. It's a common platform, so there should be no issue. Andrew Cooksey is a great resource for all of these KTM 2-stroke engines. He'd be able to give you the best advice on setup to make it more torquey. The smaller ... more »

Added reply in a thread 2 stroke guys....V-force or Rad valve? 12/28/2018 5:18 PM

Which brand works better is totally dependent on who did the most R&D. If you want it for the cool sticker on the side of the block, they both work well. I'm about to start riding/building a 2017 250SX. I'm going to start by sanding the reed block ... more »

Liked a bike check Shep's 2019 KTM 300 XC 12/21/2018 12:55 PM
Shep's 2019 KTM 300 XC
Added reply in a thread 4t oil in 2t... Yes, it can be done... 12/21/2018 9:46 AM

Dad used fork oil to make emergency premix on the trail for his IT200. That was during a race too.

Added reply in a thread FC250 or RMZ250 12/19/2018 11:38 AM

Send me a private message if you want to sell your FC250. I might be interested if the hours are low. I had a 2014 YZ250F and I really liked that bike.

Added reply in a thread 2018 KTM 250 2 STROKE: Race gas for gains???? 12/19/2018 11:35 AM

Throw another base gasket under the cylinder and retard the timing. That will make it shriek, although you might loose some of the punch.

Liked a bike check 2016 CPS Racespeed Husqvarna FC250 12/19/2018 10:54 AM
2016 CPS Racespeed Husqvarna FC250