Lives in: Driggs, ID USA

Member since: 05/18/13

Recent Activity Filter:

Reply to What yr Rmz450 wheels fit 6/1/2016 2:48 PM

Yes they will fit, and yes you can run a wider tire.

Reply to Rekluse? 5/31/2016 9:08 PM

It all depends on the version of the clutch and the adjustment. On the EXP you will have a stiffer clutch pull, and with the Core EXP it feels like stock. You can adjust you throw and have it engage a bit higher and free wheel, or a bit lower and drag ... more »

Reply to Rekluse? 5/31/2016 3:42 PM

We install them all the time and always tell customers that if they don't like it we will do a full refund including the install price..........never had to worry about it.

Reply to I'll say it first... 5/28/2016 7:41 PM

Same bike he was winning on last season. There is something wrong obviously, because his results are way under what he is capable of.

Reply to New favorite rider...Big AL ! ! 5/28/2016 3:45 PM

I'm in.

Reply to im never riding for RCH.. 5/28/2016 3:42 PM

Mechanical devices fail. I have seen it before. Kenny will make the best of a bad situation, and Hart and Carmichael will have to try to cope with the OP's decision on this one.

Reply to Stewart and Baggett 5/28/2016 8:56 AM

Much respect for both riders. I want Blake to keep strong in the points, but if he has to sit out a couple rounds and be on the podium the rest of the year I think it is worth the tradeoff. Stew.........just finish and build from there my man.

Reply to Guts seats 5/28/2016 8:52 AM

Would work out quite as well if it was Dungey.

Reply to Looking for 2007 rm250 right engine case 5/27/2016 2:43 PM

I would only buy them as a set. Honda sells separate and they work fine when doing one or the other. The other brands machine the as a set. Not saying you will, but chances for trouble with just one side are high. Transmission shafts, crank, and shift ... more »

Reply to Don't Overshoot Glen Helen's Triple Step-Up... 5/26/2016 6:17 PM

The bad thing about a wreck like that is that you have SOOOOO much time to think about what is going to happen!

Reply to Kx250f clutch kits 5/26/2016 10:29 AM

Good to hear! I have been wanting to try the Wiseco option, so this is good news.

Reply to Kick ass two strokes! 5/25/2016 8:57 PM

I'll just leave this right here.......

Reply to Kx250f clutch kits 5/25/2016 2:04 PM

Hinson, Pro-X, and DPK are all good aftermarket options. Most of the aftermarket stuff is junk and you get what you pay for with the clutches from my experience. I have guys all the time that bought a certain brand and after two rides they are needing ... more »

Reply to Is Aldon Bakers stock dropping as we speak? 5/21/2016 3:51 PM

I think Aldon will somehow weather this storm...

Reply to 2009 YZ 250F Start Issues 5/18/2016 4:43 PM

What were your intake valve clearances? Also if your cam timing is off it will not start. Make sure the marks line up at top dead center and make sure the intake valves clearances are all on the money. The center intake valve on this bike is the one ... more »

Reply to Quality RM250 Build 5/18/2016 6:57 AM

Looking great!

Reply to Hard to start when warm. 5/14/2016 12:14 PM

Do a compression test. If you were using coolant, you probably ingested some and it scarred the cylinder/piston.

Reply to 2006 YZ450f backfire! 5/10/2016 10:17 PM

Too lean on the pilot could cause this. At your elevation a 45 or 48 should be fine. I see the o ring on the fuel screws damaged a lot of the time and this will cause it as well. Another less likely thing I have seen is varnish in the nozzle (the part ... more »

Reply to White smoke coming out exhuast after starting 5/10/2016 10:09 PM

White smoke could be coolant. It usually does not go away though. Check your coolant level. If it is using coolant, it could be the head gasket. This is detectable through a leak down test. If you have bad valve guide seals they will smoke for a bit, ... more »

Reply to Suzuki 450 coming up on 75 hours 5/9/2016 8:24 AM

I would do a piston, cam chain, valve guide seals and check the valves. Cam chains are cheap and I see a lot of guys let them run loose and skip a tooth on the camshaft, which causes big issues. If you have access to do a leak down test, this would tell ... more »